Service charges
- We reserve the right to refuse any work that the gunsmith deems would make the firearm unsafe.
- We WILL NOT remove or disconnect any firearm safety and/or any component that would cause the firearm to violate federal and/or state laws.
- Service prices do not include parts or materials.
- Service prices subject to change depending on difficulty of job.
GUNSMITHING - REPAIRS |
PRICE |
Hourly Rate - Man Hour |
$80 |
Hourly Rate - Man/Machine Hour |
$100 |
Minimum Charge Per Firearm |
$20 |
Written Cost Estimate - Free if we perform the work |
$40 |
GENERAL |
PRICE |
Barrel Inspection (Borescope) - 20 caliber and above only |
$20 |
Chamber Cast |
$40 |
Clean and Inspect - Revolvers/Pistols - Rifles/Shotguns |
Starting At: $60 $80 |
Drill & Tap - Aluminum/Steel - Hardened Metal |
$40 per hole $80 per hole |
Lap Bore |
$60 |
Muzzle Device - Install (Pre-threaded barrel) - Pin/Weld |
Starting at: $40 $40 |
Polish Chamber |
$60 |
Remove Stuck Case / Bore Obstruction |
Hourly Rate |
Throat & Feed Ramp Polish - Improves feeding reliability |
$40 |
AR-15/AR-10 |
PRICING |
Assemble - Upper - Lower - Complete Rifle |
Starting At: $125 $100 $200 |
Cut/Polish Feed Ramps |
$50 - $125* |
Dimple Barrel for Gas Block - Add $40 for Disassemble/Reassemble |
$40 |
Install Gas Block & Dimple Barrel |
$60 |
Install Rear Sling Plate |
$40 |
Install Trigger |
$60 |
Replace Gas Rings |
$40 |
Replace Gas Tube |
$20 - $60* |
Replace Buffer Tube |
$60 |
Stake Castle Nut |
$20 |
*Price is determined by difficulty of disassembly/reassembly |
FINISHING |
PRICING |
Abrasive/Bead Blast/Wire Wheel (Matte) |
$100 |
Deluxe Finish (Hand sanding up to 400 grit): - Handguns - Rifles/Shotguns |
$200 $160 |
Draw Filing |
Hourly Rate |
Parkerize - Manganese (Includes Metal Prep) - Handguns - Rifles/Shotguns |
$190 - $240* $200 - $260* |
Slow Rust Bluing (Includes Metal Prep) - Handguns - Rifles/Shotguns |
$300-350* $200-450* |
*Price is determined by number of parts |
MACHINE WORK |
PRICING |
Barrel Threading |
$125 |
Milling |
Hourly Rate - Machine |
SIGHT WORK |
PRICING |
Bore sighting - Standard Scopes w/ Collimator - Simulates 100 yards |
$20 |
Front Sight Ramp - Screw On (Drill & Tap) |
See "Drill & Tap" pricing above |
Remove/Install - Dovetail - Staked - M1 Carbine (Front/Rear) |
$40 $60 $40 each |
Scope Mounting - Lap Rings - Mount and Boresight |
$20 $40 |
Shotgun Bead, Front/Mid (Drill & Tap) |
See "Drill & Tap" pricing above |
STOCK WORK |
PRICING |
Clean & Oil Finish: - Hand Rubbed (Unfilled Grain) - Hand Rubbed (Filled Grain) |
$100 - $160* $160 - $200* |
Complete Refinishing - Sand, Stain, Raise Dents, Oil |
Hourly Rate |
Inlet / Fit Stock |
Hourly Rate |
Recoil Pad Installation - Grind-to-fit - Standard (add $40 if drilling required) |
$60 $20 |
Sling Swivel Installation (Drill Stock) |
$60 |
*Price is determined by complexity of stock |
TRIGGER WORK |
PRICING |
Trigger Kit Installation (Drop-In) - Additional cost if inletting required |
$40 |
Trigger Job aka "Smooth & Tune" - Revolvers - Semi-Auto Pistols - Rifles |
$60 $80 $80 |
Trigger Pull Reduction / Spring Kit Installation |
$60 |
Please contact us about any service not listed above.
SHIP YOUR FIREARM FOR REPAIR
For guidelines on how to ship your firearm to us for service and/or repair, please click below.
For guidelines on how to ship your firearm to us for service and/or repair, please click below.